Product ID:MXM 7714/285 EPOXY/KEVLAR PREPREG
MSDS Date:01/11/1990
FSC:8305
NIIN:00F041203
MSDS Number: BXNFY

I C I COMPOSITES/FIBERITE

501 W 3RD ST
WINONA, MN 55987-5000
US

Emergency Phone: 507-454-3611

Info Phone: 507-454-3611

Preparer: BRAD DIERINGER

Cage: 0DTM1

I C I COMPOSITES/FIBERITE

WINONA, MN 55987-5000 US

Telephone: 507-454-3611

Cage: 0DTM1

ACETONE; DIMETHYL KETONE; 2-PROPANONE

CAS: 67-64-1

RTECS: AL3150000

OSHA PEL 2400 MG/CUM

ACGIH TLV: 750 PPM

EPA Report Quantity: 5000 LBS

DOT Report Quantity: 5000 LBS

2-BUTANONE (METHYL ETHYL KETONE) (MEK)

CAS: 78-93-3

RTECS: EL6475000

OSHA PEL 200 PPM

ACGIH TLV: 590 MG/CUM

EPA Report Quantity: 5000 LBS

DOT Report Quantity: 5000 LBS

KEVLAR

Fraction By Weight: 35-55%

EPOXY RESIN

Fraction By Weight: 40-50%

DIURON

CAS: 330-54-1

RTECS: YS8925000

OSHA PEL 10 MG/CUM

ACGIH TLV: 10 MG/CUM

EPA Report Quantity: 100 LBS

DOT Report Quantity: 100 LBS

ANTIMONY TRIOXIDE, ANTIMONY OXIDE

CAS: 1309-64-4

RTECS: CC5650000

Fraction By Weight: <1%

OSHA PEL 0.5 MG/CUM

ACGIH TLV: 0.5 MG/CUM (A2)

EPA Report Quantity: 1000 LBS

DOT Report Quantity: 1000 LBS

Routes of Entry: Inhalation:YES Skin:YES Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:EYES: IRRITANT. SKIN: IRRITANT,
POSSIBLE DERMATITIS/ALLERGY SENSITIZATION. VAPORS COMING OFF HEATED
MATERIAL MAY CAUSE IRRITATION. INGESTION: MAY AFFECT LIVER &
KIDNEYS.
Explanation of Carcinogenicity:NONE
Effects of Overexposure:IRRITATION
Medical Cond Aggravated by Exposure:EXISTING ALLERGIES.

First Aid:EYES: FLUSH W/WATER FOR 15 MINS. SKIN: WASH W/SOAP & WATER.
INHALATION: REMOVE TO FRESH AIR. OBTAIN MEDICAL ATTENTION IN ALL
CASES.

Extinguishing Media:CO2, DRY CHEMICAL, FOAM, WATER
Fire Fighting Procedures:USE SELF CONTAINED BREATHING APPARATUS.
EXOTHERM PROCEDURES-DISSIPATE HEAT BY SPREADING MATERIAL APART &
DOUSING W/WATER. CONTAIN EMISSIONS USING LOCAL EXHAUST.
Unusual Fire/Explosion Hazard:EXOTHERMIC POLYMERIZATION MAY OCCUR.

Spill Release Procedures:PICK UP & USE UNCONTAMINATED MATERIAL.
MATERIAL SHOULD BE PICKED UP & DISPOSED OF PROPERLY.

Handling and Storage Precautions:STORE AT/BELOW 40F. HANDLE W/CARE &
AVOID UNNECESSARY PERSONAL CONTACT.
Other Precautions:NUISANCE MATERIALS MAY BE RELEASED AS DUSTS WHEN
MACHINING CURED PRODUCTS.

Respiratory Protection:USUALLY NOT NEEDED. USE NIOSH/MSHA APPROVED
RESPIRATORS, IF NECESSARY TO CONTROL NUISANCE DUST EXPOSURE WHEN
MACHINING.
Ventilation:GOOD GENERAL VENTILATION & LOCAL EXHAUST PARTICULARLY WHERE
GRINDING/HEATING OPERATIONS OCCUR.
Protective Gloves:IMPERVIOUS
Eye Protection:SAFETY GLASSES
Other Protective Equipment:CLEAN BODY-COVERING CLOTHING
Supplemental Safety and Health

Spec Gravity:1-1.5
Appearance and Odor:IMPREGNATED FIBER W/NO ODOR
Percent Volatiles by Volume:<2/WT

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZERS, STRONG ACIDS, STRONG BASES
Stability Condition to Avoid:RAPID/EXCESSIVE HEAT
Hazardous Decomposition Products:CARBON OXIDES, NITROGEN OXIDES,
INCOMPLETELY BURNED HYDROCARBONS, AMINES, PHENOLS, ANTIMONY
COMPOUNDS, BROMINE COMPOUNDS
Conditions to Avoid Polymerization:EXOTHERMIC POLYMERIZATION CAN OCCUR
W/RAPID/EXCESSIVE HEAT.

Waste Disposal Methods:DISPOSE OF IN ACCORDANCE W/LOCAL, STATE &
FEDERAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.